78075 – MANOMETER (WATER, -2″ to 15″)
$48.38Yellow Jacket 78075 water-type manometer. Reads -2″ to 15″ W.C. for setting gas manifold pressures on natural gas and LP systems. Durable plastic construction.
Need help finding the right part?
We test parts at the counter and match the right replacement. Walk in or call ahead.
Showing 49–96 of 164 results
-
-
93266 – VACUUM PUMP (YJII, 5 CFM, 2-STAGE)
$337.32Yellow Jacket 93266 YJII vacuum pump — 5 CFM, 2-stage, 1/2 HP. Pulls down to 25 microns. Lightweight aluminum body. Workhorse pump for residential and light commercial HVAC.
-
93843 – COMPACT BALL VALVE ADAPTOR (1/4″)
$30.50Yellow Jacket 93843 compact ball valve adapter, 1/4″, 45-degree angle. Full flow for charging and recovery. Metal handle for durability.
-
A-5 – TORCH TIP (1/4″ to 3/4″)
$84.95TurboTorch A-5 torch tip for brazing 1/4″ to 3/4″ copper tubing. Air-acetylene, quick-connect fitting. One of the most common HVAC brazing tips.
-
AJ4-T – TORCH TIP ASSEMBLY (1/2″ to 1″)
$84.95TurboTorch AJ4-T torch tip assembly for brazing 1/2″ to 1″ copper. Medium flame, quick-connect fitting. Same heat range as the A-8 tip. Good all-around HVAC brazing tip.
-
AJ5-T – TORCH TIP (7/8″ to 1-5/8″)
$82.26TurboTorch AJ5-T torch tip for brazing 7/8″ to 1-5/8″ copper and soldering up to 3″. Heavy-duty output for larger commercial piping. Quick-connect fitting.
-
AR-MC – ACETYLENE REGULATOR
$113.69TurboTorch AR-MC acetylene regulator. Controls gas flow from acetylene tanks to your torch. Built-in gauge for pressure monitoring. Fits standard B tank connections.
-
ATL55 – TEST LEADS (INCLUDES ALLIGATOR CLIP ATTACHMENT)
$22.08UEi ATL55 test leads, 42-inch, CAT III 1000V rated. Right-angle banana plugs with screw-on insulated alligator clips. Replacement leads for multimeters and clamp meters.
-
ATP1 – ATTIC PRO UTILITY LIFT
$181.74Supco ATP1 Attic Pro utility lift. Safely lifts up to 250 lbs into attics or elevated spaces. 20 ft cable with adjustable length and locking hook. One-person operation.
-
B100 – INDIVIDUAL BIT HOLDER (1 PC)
$1.99Individual bit holder (1 piece). Quick-release design for fast bit changes. Standard 1/4″ hex shank fits any drill or impact driver.
-
CHIPBRUSH2 – DISPOSABLE CHIP BRUSH (2″ WIDE, SHORT)
$1.042″ disposable chip brush with natural bristles and wood handle. Use it to apply PVC glue, clean coils, brush away debris, or spread sealant. Single-use and cheap.
-
COILBRUSH – COIL BRUSH
$4.003″ nylon coil brush for cleaning condenser and evaporator coils. Loosens dirt, dust, and debris between fins without bending them. Basic HVAC maintenance tool.
-
COSOOS – UV FLASHLIGHT
$19.95COSOOS UV flashlight with 6 light modes. USB-rechargeable, aluminum body, telescoping focus lens. UV mode finds refrigerant leaks and mold fast.
-
CT-122 – SERVICE RATCHET WRENCH
$10.95CT-122 service ratchet wrench by Everwell. Four sizes in one chrome-plated tool with reversible ratchet. Built for HVAC valve and fitting work.
-
CT-14516 – MINISPLIT ADAPTOR (5/16″F to 1/4″M)
$14.43Mini-split adapter — 5/16″ female to 1/4″ male. Connects standard 1/4″ gauge hoses to R-410A mini-split service ports. Brass with quick coupler and depressor pin.
-
CT-501 – INSPECTION MIRROR
$7.86Everwell CT-501 telescopic inspection mirror with 360° swivel and chrome finish. Extends to see behind equipment and inside ductwork. Pocket-sized for field use.
-
CT-503 – MAGNETIC TELESCOPING RETRIEVAL TOOL
$6.71Everwell CT-503 telescoping magnetic retrieval tool. Extends up to 25″ with a strong magnetic head for grabbing dropped screws, bolts, and small parts. Pocket clip included.
-
DF-75 – DRAIN DAWG
$34.55DiversiTech DF-75 Drain Dawg inflatable drain tip. Fits 3/4″ and 1″ drain lines. Use with nitrogen or CO2 to blow out condensate line clogs. Rated to 140 PSI.
-
DP-1 – NITROGEN PURGE TOOL
$77.24DiversiTech DP-1 nitrogen purge tool. Adjustable flow dial for controlled nitrogen purge during brazing. Aluminum body, 50 PSI inlet. Essential for AC line work.
-
DRX3 – INFRARED REFRIGERANT LEAK DETECTOR
$692.75Fieldpiece DR82 infrared refrigerant leak detector. Detects leaks as small as 0.03 oz/yr. 10-year sensor life and 10-hour rechargeable battery. No false alarms from common gases.
-
ECBFF-1 – BALL VALVE
$18.07ECBFF-1 ball valve for refrigerant hoses. 1/4″ connection, brass construction. Controls refrigerant flow during charging, recovery, and evacuation.
-
ECMPRO – ECM MOTOR TESTER
$69.84Supco ECMPRO universal ECM motor tester. 24 VAC powered with 24-inch leads, magnetic case, and short circuit protection. Tests most ECM blower motors without the furnace board.
-
F5000 – FLARING TOOL
$99.44SPIN F5000 flaring tool set for 1/4″ to 3/4″ copper and aluminum tubing. Drill-powered (1,800 RPM) — creates flares faster than manual flaring tools.
-
FCR6 – FIN COMB (8 to 20 FINS PER INCH)
$15.65Supco FCR6 fin comb ring set — 6 color-coded combs for 8 to 20 fins per inch. Straightens bent condenser and evaporator coil fins to restore airflow.
-
FG1 – DUCT BOARD HOLE CUTTER
$50.47Malco FG1 fiberglass duct board hole cutter. Cuts 4″ to 20″ diameter holes in 1″ thick duct board. Includes utility knife blade and compass. For duct fabrication.
-
FL34 – FLINT LIGHTER
$8.35Uniweld FL34 single-flint torch lighter. Steel construction with replaceable flint. The basic spark lighter every torch setup needs. Reliable ignition for acetylene torches.
-
FSC10 – FLAME SENSOR CLEANER
$18.44Supco FSC10 flame sensor cleaner. Compact, durable tool cleans flame sensor rods in seconds. Fixes the most common cause of furnace short-cycling.
-
GG-1 – SWOOSH DRAIN GUN
$43.74DiversiTech GG-1 Swoosh Drain Gun. Uses CO2 cartridges to blast clogs out of 3/8″ to 3/4″ condensate drain lines. Portable, 800 PSI burst. Quick and effective.
-
HS-519 – CABLE TIE TENSIONING & CUTTING TOOL
$25.99HS-519 cable tie tensioning and cutting tool. Tightens zip ties to a consistent tension and flush-cuts the tail. Saves time on wire bundling jobs.
-
IRC-120 – THERMAL CAMERA
$175.00IRC-120 thermal imaging camera. Spots hot and cold spots in ductwork, finds electrical issues, and checks insulation. Compact and easy to use for HVAC diagnostics.
-
IRHT81736 – RATCHETING TUBING CUTTER
$29.97Irwin IRHT81736 ratcheting tubing cutter. Cuts copper, brass, PVC, and aluminum from 1/4″ to 1-1/8″ OD. Ratchet action for tight spaces.
-
JL3KH6 – WIRELESS REFRIGERANT CHARGE AND AIR TEST KIT
$729.55Fieldpiece JL3KH6 wireless charge and air test kit. Includes pressure probes, pipe clamps, and psychrometers for real-time HVAC diagnostics via Job Link app.
-
JL3KR4 – WIRELESS REFRIGERANT CHARGE KIT
$485.05Fieldpiece JL3KR4 wireless refrigerant charge kit. Pressure probes and pipe clamps with 1000-foot wireless range and Rapid Rail sensors for fast superheat/subcooling readings.
-
KBHC – BLADE – FG1
$12.28Malco KBHC replacement blade for the FG1 duct board hole cutter. Cuts 1.5″ thick fiberglass duct board. Durable steel blade — keeps cuts clean and precise.
-
KC100P – OXY/ACET TORCH KIT (INCLUDE TANKS AND GAS)
$605.91Uniweld KC100P oxyacetylene torch kit with tanks and gas included. Welds up to 1/8″ steel, brazes up to 1″ copper. Complete portable outfit — ready to use out of the box.
-
LT-CTB – COMPACT TUBING BENDER KIT (1/4″ – 7/8″)
$96.994LifetimeLines LT-CTB compact tubing bender kit. Bends 1/4″ to 7/8″ soft copper, aluminum, and brass tubing. Makes clean bends without kinking.
-
MAG1YL – MAGNETIC LOW VOLTAGE JUMPER WIRE
$14.95Supco MAG1YL magnetic jumper wire, 20 inches. Magnetic tips clip to terminals for hands-free HVAC diagnostics. Rated 30 VAC/VDC, 5 amps. Yellow wire.
-
MG-1 – MANIFOLD SET W/ 60″ HOSES (BRASS – R22, R410, R407A)
$79.95DiversiTech MG-1 brass manifold gauge set with 60″ hoses. Works with R-22, R-410A, and R-407C. Good starter set for DIY or light commercial work.
-
MG44 – DIGITAL WIRELESS VACUUM MICRON GAUGE (A2L)
$263.30Fieldpiece MG44 wireless vacuum micron gauge. A2L compatible, 1000-foot wireless range. Rugged design with reversible angled coupler for tight access during evacuations.
-
MR45 – REFRIGERANT RECOVERY MACHINE (A2L)
$1,048.75Fieldpiece MR45 refrigerant recovery machine. 1 HP DC motor, A2L compatible, self-purge function, three auto-stop levels. Fast, efficient recovery for all common refrigerants.
-
MSHC – DUAL CHUCK (SHORT [2″], 1/4-5/16″)
$10.71Malco MSHC dual magnetic hex chuck driver, 2″ short length. Reversible 1/4″ and 5/16″ hex sizes. Magnetic tip holds screws. Cleanable magnet design.
-
MSHC1 – DUAL CHUCK (SHORT [2″], 5/16-3/8″)
$10.58Malco MSHC1 dual magnetic hex chuck driver, 2″ short length. Reversible 5/16″ and 3/8″ hex sizes. Magnetic tip with cleanable magnet for metal shavings.
-
MSHCST – DUAL CHUCK (SAWTOOTH, SHORT [2″], 1/4-5/16″)
$29.63Malco MSHCST SawTooth dual hex driver, 2″ short length. Reversible 1/4″ and 5/16″. SawTooth tip grips stripped screws that smooth drivers slip on.
-
MSHXLC – DUAL CHUCK (LONG [6″], 1/4-5/16″)
$25.97Malco MSHXLC long-reach (6″) dual magnetic hex chuck driver. Reversible 1/4″ and 5/16″. Extra length reaches screws recessed in duct flanges and panels.
-
MSHXLC1 – DUAL CHUCK (LONG [6″], 5/16-3/8″)
$25.86Malco MSHXLC1 long-reach (6″) dual magnetic hex chuck driver. Reversible 5/16″ and 3/8″. Extra length for recessed screws on ductwork and equipment.
-
MWT-6510L – AVIATION SNIP – OFFSET – LEFT
$33.43Midwest MWT-6510L offset left-cut aviation snip. GlideTech forged blades with KUSH’N-POWER grips. Professional-grade for heavy ductwork cutting.
-
MWT-6510R – AVIATION SNIP – OFFSET – RIGHT
$33.43Midwest MWT-6510R offset right-cut aviation snip. GlideTech forged blades with KUSH’N-POWER grips. Professional-grade for heavy ductwork cutting.
-
MWT-6510S – AVIATION SNIP – OFFSET – STRAIGHT
$33.43Midwest MWT-6510S offset straight-cut aviation snip. GlideTech forged blades with KUSH’N-POWER grips. Professional-grade for straight ductwork cuts.
![MSHC - DUAL CHUCK (SHORT [2], 1/4-5/16)](https://otp-hvac.com/wp-content/uploads/2024/11/CRHEX_MSHC_reverse_action_BIT-300x300.jpg)
![MSHC1 - DUAL CHUCK (SHORT [2], 5/16-3/8)](https://otp-hvac.com/wp-content/uploads/2024/11/Malco_MSHC1-300x300.jpg)
![MSHCST - DUAL CHUCK (SAWTOOTH, SHORT [2], 1/4-5/16)](https://otp-hvac.com/wp-content/uploads/2024/11/MSHCST_SAWTOOTH_BIT-300x300.jpg)
![MSHXLC - DUAL CHUCK (LONG [6], 1/4-5/16)](https://otp-hvac.com/wp-content/uploads/2024/11/MSHXLC_HEX_DRIVER-300x300.jpg)
![MSHXLC1 - DUAL CHUCK (LONG [6], 5/16-3/8)](https://otp-hvac.com/wp-content/uploads/2024/11/MSHXLC1_HEX_DRIVER_CHUCK-300x300.png)
