DF-75 – DRAIN DAWG
DiversiTech DF-75 Drain Dawg inflatable drain tip. Fits 3/4″ and 1″ drain lines. Use with nitrogen or CO2 to blow out condensate line clogs. Rated to 140 PSI.
This is where you can browse products in this store.
Showing 1–48 of 349 results

DiversiTech DF-75 Drain Dawg inflatable drain tip. Fits 3/4″ and 1″ drain lines. Use with nitrogen or CO2 to blow out condensate line clogs. Rated to 140 PSI.

Irwin 6-in-1 SAE nut driver. Six sizes (1/4″ to 1/2″) in one compact tool. Covers the most common nut driver sizes for HVAC sheet metal screws.

ToughBuilt TB-KP-201R FoamFit Rocker knee pads. Ergonomic FoamFit design with shatter-resistant Rocker SnapShell and high side walls for all-day comfort.

ABB OT80F3 three-pole, front-operated switch-disconnector (non-fusible disconnect switch) for base or DIN-rail mounting, supplied with protected terminal clamps.

Nitrogen regulator with CGA580 connection and 1/4″ output. Use for brazing purge, pressure testing, and leak checking. Adjustable output pressure for HVAC applications.

1/2″ x 10″ black steel gas pipe nipple. Male NPT threads on both ends. For natural gas and propane piping in HVAC and plumbing systems.

1/4 in. refrigeration copper coupling with an internal stop, cup x cup. Solders two lengths of same-size ACR copper tube together; the stop centers the fitting so each tube bottoms evenly in the socket.

Fieldpiece SRS1 wired refrigerant scale. 110 lb capacity with weight alarms for charging and recovery. Water-resistant, portable, and built for field use.

SpecStar 5 CFM two-stage rotary vane vacuum pump for evacuating A/C and refrigeration systems.

ANENG VD807 non-contact voltage detector pen, 12-300V AC, with breakpoint finder, live/neutral ID and LED flashlight.

Disposable chip brush, 2 in. wide, long handle. The throwaway brush for flux, duct sealer, mastic, cements and solvents – use it and pitch it instead of cleaning it.

Universal socket that grips a range of nut and bolt sizes from a single tool.

Tubing cutter for 1/8″ to 1-1/8″ OD tubing. High-carbon steel blade with micrometer adjuster for precise cuts on copper and aluminum refrigerant lines.

Goodman/Amana OEM pull-out air conditioner disconnect used at the outdoor condensing unit to provide a local service disconnecting means.

Uniweld FL34 single-flint torch lighter. Steel construction with replaceable flint. The basic spark lighter every torch setup needs. Reliable ignition for acetylene torches.

ToughBuilt duct knife with sheath. Dual-edged blade — fine and serrated sides. Full steel tang for durability. Cuts duct board, insulation, and flex duct.

ToughBuilt TB-CT-114 journeyman electrician’s pouch with 21 pockets. ClipTech hub, tape measure clip, and wire tester slots. Versatile enough for any trade.

7/8 in. refrigeration copper 45 degree elbow, long radius, cup x cup. Handles 45 degree offsets on large suction lines in commercial and higher-tonnage residential systems.

Individual bit holder (1 piece). Quick-release design for fast bit changes. Standard 1/4″ hex shank fits any drill or impact driver.

ToughBuilt TB-66C tool backpack with 31 pockets and a laptop compartment. Rugged base protects contents. Hands-free carry for HVAC techs, electricians, and contractors.
![MSHC1 - DUAL CHUCK (SHORT [2], 5/16-3/8)](https://otp-hvac.com/wp-content/uploads/2024/11/Malco_MSHC1-300x300.jpg)
Malco MSHC1 dual magnetic hex chuck driver, 2″ short length. Reversible 5/16″ and 3/8″ hex sizes. Magnetic tip with cleanable magnet for metal shavings.

Malco 24F metal folding tool, 24 inches long. Dual folding depths (3/8″ and 1″) for bending sheet metal edges. Heavy-duty steel for ductwork fabrication.

ToughBuilt TB-CT-36-L6 technician 6-pocket pouch. Adjustable central pocket for pliers, four screwdriver loops, notebook slot, and tape clip. ClipTech hub attachment.

12-foot twin oxy-acetylene hose set, 3/16″ diameter, Grade R, 200 PSI working pressure. Standard B-fitting connections for welding and brazing setups.

Yellow Jacket 93843 compact ball valve adapter, 1/4″, 45-degree angle. Full flow for charging and recovery. Metal handle for durability.

1/2″ x 12″ black steel gas pipe nipple. Male NPT threads on both ends. For natural gas and propane piping in HVAC and plumbing systems.

Mastercool 60 in. nylon barrier charging hose set with automatic shut-off (anti-blowback) valve fittings, so refrigerant is retained in the hose when you pull it off the system.

TurboTorch Extreme self-lighting replacement tip end, factory part number 0386-1066. It is the replacement tip for the PL-12A self-lighting torch tip assembly, the largest in the self-lighting range.

10-inch adjustable channel wrench with precision jaws and non-slip handles. Chrome-plated for rust resistance. General-purpose HVAC and plumbing grip tool.

ToughBuilt TB-KP-G203-6 GelFit knee pad set, 6 pieces. Includes interchangeable Non-Marring and Rocker SnapShells so you can swap surfaces for different jobs.

Reverse (left-hand) thread adaptor for A2L refrigerant service ports, which use left-hand threads to prevent cross-connection with A1 equipment.

5% silver brazing rods (BCuP-3), 1 lb. Self-fluxing on copper-to-copper. Budget option for HVAC brazing — lower silver content, still gets the job done.

Fieldpiece SDMN5 dual-port manometer. Measures -60″ to 60″ WC for gas pressure and duct static readings. Includes adapters, magnetic hanger, and auto power-off.

2″ x 30′ self-adhesive insulation tape. Foam tape that prevents condensation on cold pipes and ducts. For HVAC, plumbing, and refrigeration lines.

TurboTorch PL-8A self-lighting torch tip assembly. Brazes 1/2″ to 1″ copper, solders 1″ to 2″ pipe. No striker needed — built-in piezo ignition for one-handed operation.
![MSHXLC - DUAL CHUCK (LONG [6], 1/4-5/16)](https://otp-hvac.com/wp-content/uploads/2024/11/MSHXLC_HEX_DRIVER-300x300.jpg)
Malco MSHXLC long-reach (6″) dual magnetic hex chuck driver. Reversible 1/4″ and 5/16″. Extra length reaches screws recessed in duct flanges and panels.

Orange wire nuts, 100-count bag. Twist-on wire connectors for 22-14 AWG copper wires. Flame-retardant. Standard for HVAC and electrical wiring.

ToughBuilt 3-inch hand seamer. Forged head with depth markings for accurate bends. Ergonomic dual-position grip for bending sheet metal edges and seams.

1/2″ black steel 90-degree street elbow. Male x Female NPT threads. Saves space by screwing directly into a fitting without a nipple.

Midwest MWT-6510S offset straight-cut aviation snip. GlideTech forged blades with KUSH’N-POWER grips. Professional-grade for straight ductwork cuts.

QwikNozzle squeeze-trigger line set flush tool, used to inject Qwik System Flush into piping and line sets where no flare fitting exists.

Mini-split adapter — 5/16″ female to 1/4″ male. Connects standard 1/4″ gauge hoses to R-410A mini-split service ports. Brass with quick coupler and depressor pin.

#8 x 1/2″ zinc hex head taper point screws, 500-pack. Self-piercing with 1/4″ zinc-plated hex head. Bulk pack for shops and contractors.

Yellow Jacket 42004 Series 41 manifold gauge set with 60″ PLUS II hoses. Brass body, 3-1/8″ gauges. Rated for R-404A, R-22, and R-410A.

Cliplight 301 valve core removal tool. Removes and installs Schrader valve cores without losing refrigerant charge. Seals the port while you work.

Fieldpiece SPK1 folding pocket thermometer. Pocketknife-style probe, -58°F to 392°F range. Quick and accurate temperature readings for HVAC field work.

UP-1 Ultimate Hub Puller. Removes seized fan blades and blower wheels from motor shafts. Adjustable arms fit various shaft sizes. Saves time on stuck hubs.

ToughBuilt TB-CT-150 ClipTech Hubs, 3-pack. Attach any ToughBuilt ClipTech pouch to any belt. Keep spares so you can swap pouches fast between jobs.