21012 – SHORT RECOVERY DRIER HOSE
SKU · 21012
$22.43
Yellow Jacket 21012 PLUS II 12-inch recovery drier hose. 1/4″ with standard flare fittings. Short hose for connecting a filter drier inline during recovery.
Need help finding the right part?
We test parts at the counter and match the right replacement. Walk in or call ahead.
All parts 1,617Equipment & Systems 119Filters & Air Quality 106Air Distribution 276Furnace & Heating 51Refrigeration 90Thermostats & Zone Controls 23Switches & Sensors 168Electrical Components 277Motors & Blower Parts 161Tools & Supplies 349
REFINETOOLS 206COPPER 34BRAZING CONSUMABLES 23PVC 18GAS PIPE 18FASTENERS 18ADHESIVE 14SERVICE DISCONNECT 5OIL 4PLASTIC DRAIN PAN 4CEILING ACCESS PANEL 31/4" SERVICE CAP 2
Showing 49–96 of 349 results
-
Low Stock
YELLOW JACKET -
Low StockYELLOW JACKET
21985 – REFRIGERANT HOSE SET (3-PACK, 60″ LONG, 1/4″ STANDARD FITTING)
SKU · 21985$100.97Yellow Jacket 21985 PLUS II hose set — 3 pack, 60″ long, 1/4″ with standard flare fittings. Red, blue, and yellow. Double barrier construction for all refrigerants.
-
In StockYELLOW JACKET
22985 – REFRIGERANT HOSE SET (3-PACK, 60″ LONG, 1/4″ LOW LOSS FITTING)
SKU · 22985$124.46Yellow Jacket 22985 PLUS II hose set — 3 pack, 60″ long, 1/4″ with SealRight low-loss fittings. Red, blue, yellow. Traps refrigerant on disconnect.
-
Low StockMILWAUKEE
2415-21 – RIGHT ANGLE DRILL KIT
SKU · MT-2415-21$117.15Milwaukee M12 cordless 3/8 in. right angle drill/driver kit. The 3-3/4 in. head length gets into joist bays, stud cavities and equipment cabinets where a standard drill will not fit.
-
Low StockUNIVERSAL
24F – METAL FOLDING TOOL
SKU · 24F$39.68Malco 24F metal folding tool, 24 inches long. Dual folding depths (3/8″ and 1″) for bending sheet metal edges. Heavy-duty steel for ductwork fabrication.
-
In StockTOLSEN
25006 – TINNING HAMMER (40oz)
SKU · 25006$16.9040oz tinning hammer with polished striking face and wooden handle. Built for bending, seaming, and forming sheet metal ductwork in HVAC installations.
-
Low StockMILWAUKEE
2504-22 – HAMMER DRILL KIT
SKU · 2504-22$189.00Milwaukee M12 FUEL 1/2 in. hammer drill kit with a POWERSTATE brushless motor, 350 in-lbs peak torque and a 6.6 in. length.
-
Low StockYELLOW JACKET
25985 – REFRIGERANT HOSE SET (3-PACK, 60″ LONG, 1/4″ BALL VALVE FITTING)
SKU · 25985$186.91Yellow Jacket 25985 PLUS II hose set — 3 pack, 60″ long, 1/4″ with FlexFlow ball valve fittings. Red, blue, yellow. Instant shutoff at the hose end.
-
Low StockASCO
2AM-T – ACETYLENE TORCH HANDLE (QUICK CONNECT)
SKU · 2AMT$81.96TurboTorch 2AM-T acetylene torch handle with quick-connect tip fitting. Extreme Swirl Technology for efficient heat distribution. The handle that most HVAC brazing tips connect to.
-
In StockVENTI
3/4C45 – REFRIGERATION COPPER FITTING (3/4″ 45° ELBOW, LONG RADIUS)
SKU · CA45R6$3.093/4 in. refrigeration copper 45 degree elbow, long radius, cup x cup. Used for 45 degree offsets on larger suction lines where a gentle turn is preferred over a hard 90. Sized by tube OD, the standard convention for ACR fittings.
-
In StockVENTI
3/4C90 – REFRIGERATION COPPER FITTING (3/4″ 90° ELBOW, LONG RADIUS)
SKU · 3/4C90$3.953/4″ ACR copper 90° long radius elbow (C x C). Wrot copper for brazing. Changes direction of refrigerant lines without restricting flow.
-
In Stock
VENTI3/4C90ST – REFRIGERATION COPPER FITTING (3/4″ 90° STREET ELBOW, LONG RADIUS)
SKU · 3/4C90ST$3.343/4″ ACR copper 90° long radius street elbow (FTG x C). One end fits inside a fitting, the other accepts pipe. Wrot copper for brazing.
-
In StockVENTI
3/4CC – REFRIGERATION COPPER FITTING (3/4″ COUPLING WITH STOP)
SKU · 3/4CC$2.263/4″ ACR copper coupling with rolled stop (C x C). Joins two pieces of 3/4″ copper pipe in a straight line. Wrot copper for brazing.
-
In StockVENTI
3/4PVC45 – PVC FITTING (3/4″, 45° ELBOW, SCH 40)
SKU · 3/4PVC45$1.313/4″ Schedule 40 PVC 45° elbow (slip x slip). Makes a gradual 45-degree turn in HVAC condensate drain lines. Better flow than a 90° elbow when space allows.
-
In StockVENTI
3/4PVC90 – PVC FITTING (3/4″, 90° ELBOW, SCH 40)
SKU · 3/4PVC90$0.853/4″ Schedule 40 PVC 90° elbow (slip x slip). Standard fitting for making right-angle turns in HVAC condensate drain lines. Glue-joint connections.
-
In Stock
VENTI3/4PVCCAP – PVC PIPE (3/4″, CAP, SCH 40, SLIP FITTING)
SKU · 3/4PVCCAP$0.683/4″ Schedule 40 PVC slip cap. Glues onto the end of 3/4″ PVC pipe to seal it off. Used on drain line dead ends, test points, and unused connections.
-
In StockVENTI
3/4PVCCPL – PVC FITTING (3/4″, COUPLING, SCH 40)
SKU · 3/4PVCCPL$0.653/4″ Schedule 40 PVC coupling (slip x slip). Joins two pieces of 3/4″ PVC pipe end-to-end. Glue-joint connection for condensate drain line repairs and extensions.
-
In Stock
VENTI3/4PVCFADAP – PVC PIPE – FEMALE ADAPTOR (SLIP x FPT, 3/4″)
SKU · 3/4FA$1.043/4″ Schedule 40 PVC female adapter (slip x FPT). Transitions from glue-joint PVC to a threaded fitting. Used on HVAC drain lines, drain pans, and cleanouts.
-
In StockVENTI
3/4PVCMADAP – PVC FITTING – NO GASKET/NUT (3/4″, THREADED MALE ADAPTOR, SCH 40)
SKU · 3/4PVCMADAP$1.173/4″ Schedule 40 PVC male adapter (slip x MPT). Transitions from glue-joint PVC to a male threaded connection. No gasket or nut included — threaded end only.
-
In StockVENTI
3/4PVCSTICK – PVC PIPE (3/4″ x 10′, SCH 40)
SKU · PVCS403/4$6.293/4″ x 10′ Schedule 40 PVC pipe. Standard for HVAC condensate drain lines. Glue-joint connections. Cut it to length on-site.
-
In StockVENTI
3/4PVCTEE – PVC FITTING (3/4″, TEE, SCH 40)
SKU · 3/4PVCTEE$1.243/4″ Schedule 40 PVC tee (slip x slip x slip). Creates a 90° branch connection in HVAC drain lines. Commonly used for cleanout access or splitting a drain run.
-
In StockSPEARS
3/4PVCTHREADEDCAP – PVC PIPE (THREADED CAP, 3/4″, SCH40)
SKU · 3/4CAP-T$1.633/4″ Schedule 40 PVC threaded cap (female pipe thread). Screws onto any 3/4″ male threaded fitting to seal the end. Used on drain line cleanouts and test ports.
-
In StockVENTI
3/4PVCTRAP – PVC FITTING (3/4″, TRAP, SCH 40)
SKU · 3/4PVCTRAP$2.823/4″ Schedule 40 PVC P-trap (slip x slip). Standard condensate drain trap for HVAC systems. Holds water to create an air seal and prevent air from blowing through the drain line.
-
Low StockUNIVERSAL
3/4SBR25 – SILVER BRAZING RING
SKU · 3/4SBR25$23.20Silver brazing rings, 3/4 in., for making brazed copper refrigerant joints. The part number indicates 25 per pack.
-
In StockPDM
3/4X50 – COPPER REFRIGERATION TUBING (3/4″ X 50′) – NO RETURNS
SKU · CT34X500D$183.163/4″ x 50′ soft copper refrigeration tubing. ACR grade — clean, dehydrated, and capped. Common suction line size for residential AC systems up to 3 tons.
-
In StockVENTI
3/8C45 – REFRIGERATION COPPER FITTING (3/8″ 45° ELBOW, LONG RADIUS)
SKU · CA45R3$2.453/8 in. refrigeration copper 45 degree elbow, long radius, cup x cup. Makes a 45 degree offset in a refrigerant line – typical on 3/8 in. liquid or small suction lines routing around framing.
-
In StockVENTI
3/8C90 – REFRIGERATION COPPER FITTING (3/8″ 90° ELBOW, LONG RADIUS)
SKU · 3/8C90$2.593/8″ ACR copper 90° long radius elbow (C x C). Wrot copper for brazing. Changes direction of refrigerant lines without restricting flow.
-
In StockVENTI
3/8C90ST – REFRIGERATION COPPER FITTING (3/8″ 90° STREET ELBOW, LONG RADIUS)
SKU · 3/8C90ST$2.603/8″ ACR copper 90° long radius street elbow (FTG x C). One end fits inside a fitting, the other accepts pipe. Wrot copper for brazing.
-
In StockVENTI
3/8CC – REFRIGERATION COPPER FITTING (3/8″ COUPLING WITH STOP)
SKU · 3/8CC$1.743/8″ ACR copper coupling with rolled stop (C x C). Joins two pieces of 3/8″ copper pipe in a straight line. Wrot copper for brazing.
-
Low StockUNIVERSAL
3/8SBR25 – SILVER BRAZING RING
SKU · 3/8SBR25$19.10Silver brazing rings, 3/8 in., for making brazed copper refrigerant joints. The part number indicates 25 per pack.
-
In StockPDM
3/8X50 – COPPER REFRIGERATION TUBING (3/8″ X 50′) – NO RETURNS
SKU · V-HLR-050-0375$77.403/8″ x 50′ soft copper refrigeration tubing. ACR grade — clean, dehydrated, and capped. Common liquid line size for residential AC systems.
-
Low StockTOLSEN
30022 – AVIATION SNIP (STRAIGHT)
SKU · 30022$10.99Straight-cut aviation snips with hardened steel blades. Cuts sheet metal, aluminum flashing, and thin steel cleanly. Ergonomic handles for all-day use.
-
Low StockTOLSEN
30023 – AVIATION SNIP (RIGHT)
SKU · 30023$9.99Right-cut aviation snips with hardened steel blades. Makes right-turning curves and straight cuts in sheet metal. Ergonomic non-slip handles.
-
In Stock
UNIVERSAL301 – VALVE CORE REMOVAL TOOL
SKU · 301$42.77Cliplight 301 valve core removal tool. Removes and installs Schrader valve cores without losing refrigerant charge. Seals the port while you work.
-
In StockHARDCAST
304100 – ROLLED MASTIC SEALANT TAPE (3″ x 100′)
SKU · HARDCAST$38.72Hardcast Foil-Grip 1402 rolled mastic sealant tape. 3″ x 100′, 17 mil thick. Butyl adhesive with aluminum foil backing. Instant water-resistant grip for duct sealing.
-
Low Stock
UNIVERSAL30V 1# – TORCH TIP (J SERIES VICTOR, LIGHT DUTY)
SKU · 30V 1#$26.54Victor 1-W-J torch tip for J Series light-duty torches. Good for smaller brazing and soldering jobs on thin copper. Precise flame control for detail work.
-
Low StockUNIVERSAL
30V 2# – TORCH TIP (J SERIES VICTOR, LIGHT DUTY)
SKU · 30V 2#$26.54Victor 2-W-J torch tip for J Series light-duty torches. Mid-range tip for general brazing and soldering on copper. Controlled heat output.
-
Low StockUNIVERSAL
30V 3# – TORCH TIP (J SERIES VICTOR, LIGHT DUTY)
SKU · 30V3#$26.54Victor 3-W-J torch tip for J Series light-duty torches. Largest in the J Series — more heat for bigger copper tubing and heavier brazing jobs.
-
Low StockWESTERN ENTERPRISES
314 – ADAPTOR (MC TANK TO B REGULATOR)
SKU · a784$25.95Western Enterprises brass cylinder adapter for the opposite direction: it lets a CGA-200 "MC" acetylene cylinder feed a CGA-520 "B" tank regulator.
-
In StockTOLSEN
33003 – MINI TUBING CUTTER (1/8-7/8)
SKU · 330522$7.99Mini tubing cutter, 1/8″ to 7/8″ OD capacity. Small enough for tight spaces around coils and line sets. Clean cuts on copper, aluminum, and brass.
-
Low StockWOKIN
33004 – TUBING CUTTER (UP TO 1-1/8″)
SKU · 330628$9.99Tubing cutter for 1/8″ to 1-1/8″ OD tubing. High-carbon steel blade with micrometer adjuster for precise cuts on copper and aluminum refrigerant lines.
-
Low StockTOLSEN
33006 – TUBING CUTTER (UP TO 2½”)
SKU · 33006$21.75Tubing cutter for up to 2-1/2″ OD. Quick-action ratcheting design cuts copper, aluminum, and plastic tubing. Handles large line sets and drain lines.
-
In StockDAKOTA SOURCING
36104 – RATCHETING PVC CUTTING TOOL
SKU · 36104$17.69Ratcheting PVC cutter — cuts plastic pipe and tubing up to 2″ with smooth, burr-free results. Ratchet action reduces hand strain on bigger cuts.
-
In StockDAKOTA SOURCING
36105 – HOLE CUTTER
SKU · 36105$47.89Adjustable hole cutter for sheet metal. Creates clean circular holes for ductwork, vents, and registers. Fits in a standard drill chuck.
-
In Stock
DAKOTA SOURCING36106 – REPLACEMENT BITS FOR 36105 (5PC)
SKU · 36106$25.865-pack replacement bits for the 36105 adjustable hole cutter. Hardened steel for clean, burr-free cuts in sheet metal ductwork.
-
In StockDAKOTA SOURCING
36113 – DUCT KNIFE (DOUBLE SIDED – SERRATED & STRAIGHT)
SKU · 36113$15.15Double-sided duct knife with serrated and straight edges. Ergonomic handle and puncture-resistant sheath included. Cuts duct board, insulation, and flex duct.
-
In StockTOLSEN
38013 – SCREWDRIVER SET (6PC, INSULATED)
SKU · 38013$15.896-piece insulated screwdriver set rated to 1000V. Phillips and slotted tips with ergonomic handles. Required for safe electrical and HVAC work.
-
Out of StockYELLOW JACKET
42004 – REFRIGERANT MANIFOLD GAUGES (R404A/R22/R410A, BRASS, 5′ HOSE SET)
SKU · 42004$175.55Yellow Jacket 42004 Series 41 manifold gauge set with 60″ PLUS II hoses. Brass body, 3-1/8″ gauges. Rated for R-404A, R-22, and R-410A.
Showing 96 of 349 parts