COILBRUSH – COIL BRUSH
SKU · COILBRUSH
$4.00
3″ nylon coil brush for cleaning condenser and evaporator coils. Loosens dirt, dust, and debris between fins without bending them. Basic HVAC maintenance tool.
Product images are representative. Always verify compatibility with your model number before visiting us in store.
Need help finding the right part?
We test parts at the counter and match the right replacement. Walk in or call ahead.
All parts 1,291Equipment & Systems 67Filters & Air Quality 83Air Distribution 259Furnace & Heating 39Refrigeration 67Thermostats & Zone Controls 17Switches & Sensors 132Electrical Components 224Motors & Blower Parts 129Tools & Supplies 276
Showing 1–48 of 164 results
-
In Stock
UNIVERSAL -
Out of Stock
UNIVERSALUP-1 – ULTIMATE HUB PULLER
SKU · UP1$63.33UP-1 Ultimate Hub Puller. Removes seized fan blades and blower wheels from motor shafts. Adjustable arms fit various shaft sizes. Saves time on stuck hubs.
-
In Stock
UNIVERSAL0125 – PVC CUTTING TOOL (3/8″ to 1″)
SKU · 36101$13.19PVC cutting tool for 3/8″ to 1″ pipe. One-hand ratcheting design for clean cuts on condensate drain lines and small PVC pipes.
-
In Stock
UNIVERSAL33003 – MINI TUBING CUTTER (1/8-7/8)
SKU · 330522$7.99Mini tubing cutter, 1/8″ to 7/8″ OD capacity. Small enough for tight spaces around coils and line sets. Clean cuts on copper, aluminum, and brass.
-
Low Stock
UNIVERSALSRS1 – WIRED REFRIGERANT SCALE
SKU · SRS1$235.45Fieldpiece SRS1 wired refrigerant scale. 110 lb capacity with weight alarms for charging and recovery. Water-resistant, portable, and built for field use.
-
In Stock
UNIVERSAL21985 – REFRIGERANT HOSE SET (3-PACK, 60″ LONG, 1/4″ STANDARD FITTING)
SKU · 21985$100.97Yellow Jacket 21985 PLUS II hose set — 3 pack, 60″ long, 1/4″ with standard flare fittings. Red, blue, and yellow. Double barrier construction for all refrigerants.
-
In Stock
UNIVERSALCHIPBRUSH2 – DISPOSABLE CHIP BRUSH (2″ WIDE, SHORT)
SKU · CHIPBRUSH2$1.042″ disposable chip brush with natural bristles and wood handle. Use it to apply PVC glue, clean coils, brush away debris, or spread sealant. Single-use and cheap.
-
Low Stock
UNIVERSAL24F – METAL FOLDING TOOL
SKU · 24F$39.68Malco 24F metal folding tool, 24 inches long. Dual folding depths (3/8″ and 1″) for bending sheet metal edges. Heavy-duty steel for ductwork fabrication.
-
In Stock
UNIVERSAL36113 – DUCT KNIFE (DOUBLE SIDED – SERRATED & STRAIGHT)
SKU · 36113$15.15Double-sided duct knife with serrated and straight edges. Ergonomic handle and puncture-resistant sheath included. Cuts duct board, insulation, and flex duct.
-
In Stock
UNIVERSALRC-1 – LIQUID CHARGING ADAPTER
SKU · RC1$19.47DiversiTech RC-1 liquid charging adapter. Converts liquid refrigerant to vapor before it enters the compressor. Protects the compressor during charging.
-
Low Stock
UNIVERSALTB-KP-2B – FOAMFIT KNEE PADS
SKU · TB-KP-2B-2BES$20.99ToughBuilt TB-KP-2B FoamFit knee pads. Ergonomic FoamFit design with high side walls and EVA elastic straps. Solid mid-range option for HVAC and construction.
-
In Stock
UNIVERSAL16569 – 6-IN-1 SCREWDRIVER
SKU · screwdriver$5.996-in-1 multi-bit screwdriver with Phillips, slotted, and nut driver tips. One tool handles most HVAC panel screws and terminal connections.
-
In Stock
UNIVERSALSPK1 – STICK THERMOMETER
SKU · SPK1$35.15Fieldpiece SPK1 folding pocket thermometer. Pocketknife-style probe, -58°F to 392°F range. Quick and accurate temperature readings for HVAC field work.
-
Out of Stock
UNIVERSALTB-H4S5-23FU – FOLDING JAB SAW + BLADES
SKU · TB-H4S5-23FU$22.99ToughBuilt folding jab saw with 5 replacement blades. Quick-release blade swap. Folds for pocket carry. Cuts drywall, duct board, and insulation.
-
Low Stock
UNIVERSALRCB1 – REFRIGERATION COIL BRUSH
SKU · RCB1$8.69Supco RCB1 refrigeration coil brush, 27.5″ long with dual bristle lengths. Cleans between condenser and evaporator coil fins. Wooden handle.
-
In Stock
UNIVERSAL25985 – REFRIGERANT HOSE SET (3-PACK, 60″ LONG, 1/4″ BALL VALVE FITTING)
SKU · 25985$186.91Yellow Jacket 25985 PLUS II hose set — 3 pack, 60″ long, 1/4″ with FlexFlow ball valve fittings. Red, blue, yellow. Instant shutoff at the hose end.
-
In Stock
UNIVERSAL301 – VALVE CORE REMOVAL TOOL
SKU · 301$42.77Cliplight 301 valve core removal tool. Removes and installs Schrader valve cores without losing refrigerant charge. Seals the port while you work.
-
Low Stock
UNIVERSALTB-KP-G203-6 – 6 PC. GELFIT KNEE PAD SET
SKU · TB-KP-G203-6$41.99ToughBuilt TB-KP-G203-6 GelFit knee pad set, 6 pieces. Includes interchangeable Non-Marring and Rocker SnapShells so you can swap surfaces for different jobs.
-
Low Stock
UNIVERSAL33006 – TUBING CUTTER (UP TO 2½”)
SKU · 33006$21.75Tubing cutter for up to 2-1/2″ OD. Quick-action ratcheting design cuts copper, aluminum, and plastic tubing. Handles large line sets and drain lines.
-
Low Stock
UNIVERSALMR45 – REFRIGERANT RECOVERY MACHINE (A2L)
SKU · MR45$1,174.70Fieldpiece MR45 refrigerant recovery machine. 1 HP DC motor, A2L compatible, self-purge function, three auto-stop levels. Fast, efficient recovery for all common refrigerants.
-
In Stock
UNIVERSAL93843 – COMPACT BALL VALVE ADAPTOR (1/4″)
SKU · 93843$30.50Yellow Jacket 93843 compact ball valve adapter, 1/4″, 45-degree angle. Full flow for charging and recovery. Metal handle for durability.
-
In Stock
UNIVERSALCT-14516 – MINISPLIT ADAPTOR (5/16″F to 1/4″M)
SKU · ADAPTER410$14.43Mini-split adapter — 5/16″ female to 1/4″ male. Connects standard 1/4″ gauge hoses to R-410A mini-split service ports. Brass with quick coupler and depressor pin.
-
In Stock
UNIVERSAL48-32-4803 – BIT HOLDER
SKU · A-969-36$2.99Milwaukee 48-32-4803 magnetic bit holder. 3-inch impact-duty design locks bits tight during high-torque driving. Fits all standard 1/4″ hex shank bits.
-
In Stock
UNIVERSALSC260 – CLAMP METER
SKU · SC260$160.65Fieldpiece SC260 compact clamp meter. True RMS, 400A AC, 600V AC/DC with temperature measurement and backlight. A solid everyday meter for HVAC work.
-
In Stock
UNIVERSALGG-1 – SWOOSH DRAIN GUN (GALLO GUN)
SKU · GG-1$44.59DiversiTech GG-1 Swoosh Drain Gun. Uses CO2 cartridges to blast clogs out of 3/8″ to 3/4″ condensate drain lines. Portable, 800 PSI burst. Quick and effective.
-
In Stock
UNIVERSAL19209 – SEALRIGHT FITTING (ELBOW, 1/4″, LOW LOSS)
SKU · 19209$21.90Yellow Jacket 19209 SealRight 1/4″ 90-degree low-loss fitting. Traps refrigerant automatically when you disconnect. Male flare, elbow design for tight spaces.
-
Low Stock
UNIVERSALMG44 – DIGITAL WIRELESS VACUUM MICRON GAUGE (A2L)
SKU · MG44$269.45Fieldpiece MG44 wireless vacuum micron gauge. A2L compatible, 1000-foot wireless range. Rugged design with reversible angled coupler for tight access during evacuations.
-
Low Stock
UNIVERSALJL3KR4 – WIRELESS REFRIGERANT CHARGE KIT
SKU · JL3KR4$504.90Fieldpiece JL3KR4 wireless refrigerant charge kit. Pressure probes and pipe clamps with 1000-foot wireless range and Rapid Rail sensors for fast superheat/subcooling readings.
-
Low Stock
UNIVERSALPE44 – PIN EXTRACTOR TOOL
SKU · PE44$25.40ESP PE44 pin extractor tool. Removes and reinserts AMP and Molex pins from HVAC wire harness connectors without cutting or splicing wires.
-
Low Stock
UNIVERSALMWT-6510L – AVIATION SNIP – OFFSET – LEFT
SKU · MWT-6510L$37.06Midwest MWT-6510L offset left-cut aviation snip. GlideTech forged blades with KUSH’N-POWER grips. Professional-grade for heavy ductwork cutting.
-
Low Stock
UNIVERSALSW-MFRB – FLAME RESISTANT BLANKET
SKU · SW-MFRB$58.5618″x18″ flame-resistant magnetic blanket for brazing in tight spaces. Integrated magnets stick to metal surfaces, reinforced grommets, and center slit for pipes. Protects walls and wiring.
-
In Stock
UNIVERSALPL-8A – SELF LIGHTING TORCH TIP ASSEMBLY (1/2″ to 1″)
SKU · 0386-0819$146.64TurboTorch PL-8A self-lighting torch tip assembly. Brazes 1/2″ to 1″ copper, solders 1″ to 2″ pipe. No striker needed — built-in piezo ignition for one-handed operation.
-
In Stock
UNIVERSAL15660 – REFRIGERANT HOSE (3/8″ HOSE, 5′ LONG)
SKU · 15660$70.98Yellow Jacket 15660 heavy-duty 3/8″ charging and vacuum hose, 60″ (5 ft). 600 psi working pressure, 3000 psi burst. For larger systems and faster vacuum pulldown.
-
Low Stock
UNIVERSALMWT-C5 – SHEET METAL CRIMPER (5-BLADE)
SKU · MWT-C5$36.99Midwest MWT-C5 five-blade sheet metal crimper. 1-5/8″ throat depth with KUSH’N-POWER handles. Creates crimps for joining round duct fittings.
-
Low Stock
UNIVERSALSTCR50191/2-1M – 1/2 STAPLE – 1,000PK
SKU · STCR50191/2-1M$12.03STCR5019 1/2″ staples, 1,000-pack. Heavy-duty staples for insulation, duct wrap, and upholstery. Fits Arrow T50 and compatible staplers.
-
Low Stock
UNIVERSALTB-KP-201R – FOAMFIT ROCKER KNEE PADS
SKU · TB-KP-201R-2BES$28.99ToughBuilt TB-KP-201R FoamFit Rocker knee pads. Ergonomic FoamFit design with shatter-resistant Rocker SnapShell and high side walls for all-day comfort.
-
Low Stock
UNIVERSALDRX3 – INFRARED REFRIGERANT LEAK DETECTOR
SKU · DRX3$692.75Fieldpiece DR82 infrared refrigerant leak detector. Detects leaks as small as 0.03 oz/yr. 10-year sensor life and 10-hour rechargeable battery. No false alarms from common gases.
-
Low Stock
UNIVERSALTB-CT-61-18 – XL ROLLING MASSIVE MOUTH BAG
SKU · TB-CT-61-18$176.99ToughBuilt TB-CT-61-18 XL rolling Massive Mouth tool bag. Patented wide-open design, hard body, rolling wheels, and telescoping handle. Haul your full tool kit without lifting.
-
Low Stock
UNIVERSALSM382V – DIGITAL MANIFOLD (A2L)
SKU · SM382V$623.05Fieldpiece SM382V digital refrigerant manifold. A2L compatible, wireless Job Link connectivity, built-in vacuum gauge. Reads pressure, temperature, superheat, and subcooling.
-
Low Stock
UNIVERSALTB-CT-62-20 – X-LARGE MASSIVE MOUTH BAG (20″, WATERPROOF)
SKU · TB-CT-62-20-1BES$99.99ToughBuilt TB-CT-62-20 X-large Massive Mouth tool bag, 20-inch, waterproof bottom. Biggest non-rolling bag in the Massive Mouth line. Hard body with rugged base.
-
In Stock
UNIVERSALF5000 – FLARING TOOL
SKU · F5000$99.44SPIN F5000 flaring tool set for 1/4″ to 3/4″ copper and aluminum tubing. Drill-powered (1,800 RPM) — creates flares faster than manual flaring tools.
-
Low Stock
UNIVERSALTB-94-M-3 – FASTENER BAGS (3 FASTENER BAGS)
SKU · TB-94-M-3-2BES$10.99ToughBuilt TB-94-M-3 mesh fastener bags, 3-pack. Heavy-duty mesh windows for visibility. Top-mount carabiner clips for hanging. Organize screws, fittings, and small parts.
-
In Stock
UNIVERSALIRHT81736 – RATCHETING TUBING CUTTER
SKU · 42080$29.97Irwin IRHT81736 ratcheting tubing cutter. Cuts copper, brass, PVC, and aluminum from 1/4″ to 1-1/8″ OD. Ratchet action for tight spaces.
-
Low Stock
UNIVERSALKC100P – OXY/ACET TORCH KIT (INCLUDE TANKS AND GAS)
SKU · G-150-J-PT$605.91Uniweld KC100P oxyacetylene torch kit with tanks and gas included. Welds up to 1/8″ steel, brazes up to 1″ copper. Complete portable outfit — ready to use out of the box.
-
Out of Stock
UNIVERSALTB-CT-36-L6 – TECHNICIAN 6-POCKET POUCH
SKU · TB-CT-36-L6-2BES$18.99ToughBuilt TB-CT-36-L6 technician 6-pocket pouch. Adjustable central pocket for pliers, four screwdriver loops, notebook slot, and tape clip. ClipTech hub attachment.
-
In Stock
UNIVERSALTB-H4-60-L – AVIATION SNIPS (LEFT)
SKU · TB-H4-60-L-6BES$17.99ToughBuilt left-cut aviation snips. Induction-hardened forged blades with dual grip positions. Flush-cut design for tight ductwork trimming.
-
Low Stock
UNIVERSAL1948778 – 6-IN-1 NUT DRIVER
SKU · 1948778$14.98Irwin 6-in-1 SAE nut driver. Six sizes (1/4″ to 1/2″) in one compact tool. Covers the most common nut driver sizes for HVAC sheet metal screws.
-
Low Stock
UNIVERSAL93266 – VACUUM PUMP (YJII, 5 CFM, 2-STAGE)
SKU · 93266$337.32Yellow Jacket 93266 YJII vacuum pump — 5 CFM, 2-stage, 1/2 HP. Pulls down to 25 microns. Lightweight aluminum body. Workhorse pump for residential and light commercial HVAC.
Showing 48 of 164 parts