3/4WHIP – ELECTRICAL WHIP (6′, #8)
$28.826′ electrical whip with #8 gauge wire and 3/4″ liquid-tight non-metallic conduit. Connects your AC disconnect to the condenser. Pre-wired and ready to install.
Showing 145–192 of 1291 results
-
-
3/4X50 – COPPER REFRIGERATION TUBING (3/4″ X 50′)
$183.163/4″ x 50′ soft copper refrigeration tubing. ACR grade — clean, dehydrated, and capped. Common suction line size for residential AC systems up to 3 tons.
-
3/8C90 – REFRIGERATION COPPER FITTING (3/8″ 90° ELBOW, LONG RADIUS)
$2.503/8″ ACR copper 90° long radius elbow (C x C). Wrot copper for brazing. Changes direction of refrigerant lines without restricting flow.
-
3/8C90ST – REFRIGERATION COPPER FITTING (3/8″ 90° STREET ELBOW, LONG RADIUS)
$2.603/8″ ACR copper 90° long radius street elbow (FTG x C). One end fits inside a fitting, the other accepts pipe. Wrot copper for brazing.
-
3/8CC – REFRIGERATION COPPER FITTING (3/8″ COUPLING WITH STOP)
$1.723/8″ ACR copper coupling with rolled stop (C x C). Joins two pieces of 3/8″ copper pipe in a straight line. Wrot copper for brazing.
-
3/8X50 – COPPER REFRIGERATION TUBING (3/8″ X 50′)
$77.403/8″ x 50′ soft copper refrigeration tubing. ACR grade — clean, dehydrated, and capped. Common liquid line size for residential AC systems.
-
30/440 – CAPACITOR (ROUND, MADE IN USA)
$24.9130 MFD 440V round run capacitor. Powers a single motor — compressor or fan. American-made by Titan HD with 60,000-hour rated life.
-
30/5/440 – DUAL CAPACITOR (ROUND, MADE IN USA)
$35.7530+5 MFD 440V dual run capacitor. Powers both the compressor and condenser fan motor. Fits most residential AC systems. American-made by Titan HD.
-
30/7.5/440 – DUAL CAPACITOR (ROUND, MADE IN USA)
$41.2830+7.5 MFD 440V dual run capacitor. Powers both the compressor and condenser fan motor. Fits most residential AC systems. American-made by Titan HD.
-
30+5X440 – DUAL CAPACITOR (ROUND, MADE OVERSEAS)
$28.0030+5 MFD 440V dual run capacitor. Powers both the compressor and condenser fan motor. Budget-friendly TrueLine replacement for residential AC.
-
30+7.5X440 – DUAL CAPACITOR (ROUND, MADE OVERSEAS)
$28.3030+7.5 MFD 440V dual run capacitor. Powers both the compressor and condenser fan motor. Budget-friendly TrueLine replacement for residential AC.
-
30005 – DAMPER (5″ W/ KEY)
$6.435″ round duct damper with key handle. Controls airflow to individual rooms by opening or closing the damper blade. Galvanized steel.
-
30006 – DAMPER (6″ W/ KEY)
$4.936″ round duct damper with key handle. Controls airflow to individual rooms by opening or closing the damper blade. Galvanized steel.
-
30007 – DAMPER (7″ W/ KEY)
$5.097″ round duct damper with key handle. Controls airflow to individual rooms by opening or closing the damper blade. Galvanized steel.
-
30008 – DAMPER (8″ W/ KEY)
$5.198″ round duct damper with key handle. Controls airflow to individual rooms by opening or closing the damper blade. Galvanized steel.
-
30009 – DAMPER (9″ W/ KEY)
$7.369″ round duct damper with key handle. Controls airflow to individual rooms by opening or closing the damper blade. Galvanized steel.
-
30010 – DAMPER (10″ W/ KEY)
$7.6710″ round duct damper with key handle. Controls airflow to individual rooms by opening or closing the damper blade. Galvanized steel.
-
30012 – DAMPER (12″ W/ KEY)
$8.3912″ round duct damper with key handle. Controls airflow to individual rooms by opening or closing the damper blade. Galvanized steel.
-
30014 – DAMPER (14″ W/ KEY)
$10.7914″ round duct damper with key handle. Controls airflow to individual rooms by opening or closing the damper blade. Galvanized steel.
-
30016 – DAMPER (16″ W/ KEY)
$12.8316″ round duct damper with key handle. Controls airflow to individual rooms by opening or closing the damper blade. Galvanized steel.
-
30022 – AVIATION SNIP (STRAIGHT)
$10.99Straight-cut aviation snips with hardened steel blades. Cuts sheet metal, aluminum flashing, and thin steel cleanly. Ergonomic handles for all-day use.
-
30023 – AVIATION SNIP (RIGHT)
$9.99Right-cut aviation snips with hardened steel blades. Makes right-turning curves and straight cuts in sheet metal. Ergonomic non-slip handles.
-
301 – VALVE CORE REMOVAL TOOL
$42.77Cliplight 301 valve core removal tool. Removes and installs Schrader valve cores without losing refrigerant charge. Seals the port while you work.
-
3030-3 – EQUIPMENT PAD (30″X30″ – 3″)
$47.7530″ x 30″ x 3″ plastic equipment pad for outdoor AC units and heat pumps. Blow-molded, UV-resistant, lightweight. Keeps your condenser level and off the dirt.
-
304100 – ROLLED MASTIC SEALANT TAPE (3″ x 100′)
$37.74Hardcast Foil-Grip 1402 rolled mastic sealant tape. 3″ x 100′, 17 mil thick. Butyl adhesive with aluminum foil backing. Instant water-resistant grip for duct sealing.
-
30V 1# – TORCH TIP (J SERIES VICTOR, LIGHT DUTY)
$26.54Victor 1-W-J torch tip for J Series light-duty torches. Good for smaller brazing and soldering jobs on thin copper. Precise flame control for detail work.
-
30V 2# – TORCH TIP (J SERIES VICTOR, LIGHT DUTY)
$26.54Victor 2-W-J torch tip for J Series light-duty torches. Mid-range tip for general brazing and soldering on copper. Controlled heat output.
-
30V 3# – TORCH TIP (J SERIES VICTOR, LIGHT DUTY)
$26.54Victor 3-W-J torch tip for J Series light-duty torches. Largest in the J Series — more heat for bigger copper tubing and heavier brazing jobs.
-
310371-752 – INDUCER MOTOR ASSEMBLY (CARRIER, AFTERMARKET, DIRECT, 66752)
$257.69Aftermarket inducer motor assembly for Carrier furnaces. 115V, 3200 RPM. Direct replacement for 310371-752. Includes motor, housing, wheel, and gasket — complete swap.
-
313BOX – PLEATED FILTER (APRILAIRE REPLACEMENT, MERV 13)
$46.60Aftermarket 313BOX replacement for Aprilaire 310/313. MERV 13, 20x20x4. Same filtration as the OEM filter at a lower price. Fits Aprilaire 1310, 2310, 3310, and 4300.
-
318984-753 – INDUCER MOTOR (CARRIER, AFTERMARKET, DIRECT, SM4753)
$95.50Aftermarket inducer motor for Carrier furnaces. 115V, 1/25 HP, 3300 RPM. Replaces 318984-753, HC21ZE114, HC21ZE117, and HC21ZE123. Fits a wide range of Carrier models.
-
320887-751 – INDUCER MOTOR GASKET KIT (CARRIER)
$35.83Carrier OEM inducer motor gasket kit. Seals the inducer motor housing to prevent exhaust gas leaks. Use when replacing the inducer motor or if you smell exhaust fumes near the furnace.
-
325878-751 – CONTROL BOARD (CARRIER, DIRECT, AFTERMARKET, 50M56U-751)
$244.98Carrier 325878-751 control board (50M56U-751 aftermarket). Fits 58STA and 58ZAV series Carrier furnaces. Manages gas valve, ignition, and blower operations.
-
326100-401 – INDUCER COOLING WHEEL
$25.19Carrier OEM inducer cooling fan wheel. Part 326100-401, also listed as LA660003. Cools the inducer motor during operation. Replace if cracked or wobbling.
-
326628-761 – INDUCER MOTOR ASSEMBLY (CARRIER, AFTERMARKET, DIRECT, P326628-761)
$229.44Aftermarket inducer motor assembly for Carrier furnaces. Two-speed, thermally protected. Replaces 326628-761 and multiple cross-references. Complete assembly by Packard (66761).
-
33003 – MINI TUBING CUTTER (1/8-7/8)
$7.99Mini tubing cutter, 1/8″ to 7/8″ OD capacity. Small enough for tight spaces around coils and line sets. Clean cuts on copper, aluminum, and brass.
-
33004 – TUBING CUTTER (UP TO 1-1/8″)
$9.99Tubing cutter for 1/8″ to 1-1/8″ OD tubing. High-carbon steel blade with micrometer adjuster for precise cuts on copper and aluminum refrigerant lines.
-
33006 – TUBING CUTTER (UP TO 2½”)
$21.75Tubing cutter for up to 2-1/2″ OD. Quick-action ratcheting design cuts copper, aluminum, and plastic tubing. Handles large line sets and drain lines.
-
332505-751 – IGNITOR (CARRIER, AFTERMARKET, DIRECT, SSN086KS)
$63.21Silicon nitride ignitor for Carrier/Bryant furnaces. 120V. Replaces 332505-751 and LH33ZG001. Direct replacement SSN086KS.
-
349336-762 – INDUCER MOTOR ASSEMBLY (CARRIER, AFTERMARKET, DIRECT, P326628-762)
$231.02Aftermarket inducer motor assembly for Carrier furnaces. Replaces 349336-762 and 326628-762. Complete assembly with motor, housing, and wheel. Packard 66762.
-
349336-763 – INDUCER MOTOR ASSEMBLY (CARRIER, 2-STAGE, DIRECT REPLACEMENT, P326628-763)
$232.31Aftermarket two-stage inducer motor assembly for Carrier furnaces. 115V, 3000 RPM, two-speed. Replaces 349336-763 and 326628-763. Complete assembly by Packard (66763).
-
35/10/440 – DUAL CAPACITOR (ROUND, MADE IN USA)
$41.9635+10 MFD 440V dual run capacitor. Powers both the compressor and condenser fan motor. Fits most residential AC systems. American-made by Titan HD.
-
35/440 – CAPACITOR (ROUND, MADE IN USA)
$25.6835 MFD 440V round run capacitor. Powers a single motor — compressor or fan. American-made by Titan HD with 60,000-hour rated life.
-
35/5/440 – DUAL CAPACITOR (ROUND, MADE IN USA)
$36.2435+5 MFD 440V dual run capacitor. Powers both the compressor and condenser fan motor. Fits most residential AC systems. American-made by Titan HD.
-
35/7.5/440 – DUAL CAPACITOR (ROUND, MADE IN USA)
$37.2035+7.5 MFD 440V dual run capacitor. Powers both the compressor and condenser fan motor. Fits most residential AC systems. American-made by Titan HD.
-
35+10X440 – DUAL CAPACITOR (ROUND, MADE OVERSEAS)
$29.7635+10 MFD 440V dual run capacitor. Powers both the compressor and condenser fan motor. Budget-friendly Supco replacement for residential AC.
-
35+5X440 – DUAL CAPACITOR (ROUND, MADE OVERSEAS)
$28.4535+5 MFD 440V dual run capacitor. Powers both the compressor and condenser fan motor. Budget-friendly TrueLine replacement for residential AC.
-
35+7.5X440 – DUAL CAPACITOR (ROUND, MADE OVERSEAS)
$28.5535+7.5 MFD 440V dual run capacitor. Powers both the compressor and condenser fan motor. Budget-friendly TrueLine replacement for residential AC.
