
35/440 – CAPACITOR (ROUND, MADE IN USA)
Bring the old cap in — we bench-test it free at the counter, and you'll know in two minutes whether it actually failed. Match the MFD exactly; voltage can go up (440V replaces 370V) but never down.
10226 Plano Rd, Suite 104, Dallas TX 75238
Questions? Call or text (214) 340-9421
Mon–Fri 10 am – 7 pm | Sat 10 am – 3 pm
Symptoms of failure
- AC hums but the fan and compressor will not start
- Outdoor fan only starts if you push it with a stick
- Compressor tries to start, clicks, then trips the breaker
- System short-cycles or runs warm on a hot afternoon
- The capacitor top is domed, split, or leaking oil
- Unit worked this morning and quit in the heat of the day
Seeing these does not always mean this part is the culprit. Bring the old one in and we will meter it at the counter, free, before you buy.
If your AC won’t start, hums but doesn’t kick on, or runs but won’t cool, a bad capacitor is the most common cause. This 35 MFD round cap powers a single motor — compressor or condenser fan. Replace when the motor hums but won’t kick on.
Replaces: Universal — matches by MFD and voltage.
Fits: Fits most residential HVAC systems using this value. Bring your old cap or model number — we match at the counter.
Need help? See our AC Not Cooling Troubleshooting Guide or Capacitor Cross-Reference Chart.
In stock at Open To Public HVAC Parts in Dallas. We test parts at the counter before you buy. Call or text (214) 340-9421.
Specs
- Capacitance35 MFD
- Voltage440V (compatible with lower-voltage applications)
- Tolerance±6%
- Frequency50/60 Hz
- TypeSingle-run capacitor
- ShapeRound
- TerminalsQuick-connect
- UL ListedYes
- OriginUSA-made
Installing it yourself
- Kill power at the disconnect and confirm 0V. A capacitor stores a lethal charge with the power off.
- Discharge it: bridge the terminals with an insulated-handle screwdriver, or a 20k ohm resistor, then confirm 0V with a meter.
- Photograph the wiring before you pull a single wire. HERM, FAN and C are not interchangeable.
- Loosen the mounting strap and lift the old capacitor out.
- Match MFD exactly. Voltage may go up (370V to 440V) but never down.
- Land the wires on the same terminals, strap it down, restore power.
- Never handle a swollen or leaking capacitor by the terminals - bring it in and we will dispose of it.
Power off at the disconnect first, every time. Not sure partway through? Bring it to the counter and we will walk it with you.
Cross-reference numbers
This part replaces the following OEM and aftermarket numbers:
- 12715
- 35440
- 43-TL35004-R
- CAP-35440R
- CAP035040440ST
- CAP350000440
- CR35X440R
- P291-3504R
- SA2214
- TP-CAP-35440R
Not sure if your number matches? Call (214) 340-9421 or bring the old part in — bench-testing is free.
Fits these models
- Condenser fan motors, blower motors, or other PSC motors requiring matching MFD at 370V or 440V run capacitor
- Common on small condensers, mini-splits, range hoods, and OEM blower assemblies
- Verify motor data plate calls for matching MFD before swapping
How do I know if my run capacitor is bad?
The motor it powers (fan or blower) won't start, hums but doesn't spin, runs slow, or trips on overload. We bench-test these free at the counter — bring it in.
Can I use a higher MFD rating?
No. Match MFD exactly to the motor's data plate. Higher MFD over-amps the windings and shortens motor life. Voltage rating can go UP (440V replaces 370V) but never down.
Does shape (oval vs round) matter?
Electrically no — same value works in either shape. Fitment in your cap bracket might. Bring the old one in and we'll match the form factor.
Do I need to discharge it before removing?
Yes — even an "off" cap holds 240V+ that bites hard. Short the terminals with an insulated screwdriver for 5 seconds before disconnecting.




